Connecting a Subwoofer To an Old Amplifier is an easy task. Follow this guide and you will find easy steps.
You have just purchased your brand new surround sound system and you are eager to start hooking it up. As you connect the speakers, you notice that your receiver doesn’t quite seem to be getting everything. There is some noise in your speaker cables and you are afraid that this connection is going to stop your music system from sounding good. But of course, you already know this. So, instead of trying to hook your new subwoofers to your new amplifier, why not try to connect them to their own amps?
This might sound like an odd suggestion, but it makes a lot of sense. It used to be that connecting amplifiers to home audio systems was something that low-end bass players did because they did not have the option of connecting their amps to their speakers. The days are gone, however, and the latest technology makes it possible for anyone to connect their low-end bass system to their amps. If you do not know how to connect a subwoofer to an old amplifier, or if you want to replace your old amp with a high end model, then this could be your solution. All that you need is a vintage amp that has a preamp input and uses crossovers to send the signal to your speakers. With the amplifier connected to your speakers, all that is left for you to do is use the appropriate wire to hook up the amp to the speakers.
Before you get started, however, there are a few steps that you will need to follow. The first step is to set up your stereo’s speakers so that they will work with your home audio system. Some people mistakenly think that their units require separate cables to work with their amplifiers, but this is simply not true. True, separate cables are required in some cases, but the majority of units simply use one cable that is split between the amplifier and the stereo subwoofers. This is the important information that you need to remember when learning how to connect a subwoofer to an old amplifier.
Once you have the speakers set up, you need to find out just how to connect a subwoofer to an old amplifier. You may have noticed that the volume level will drop significantly with a passive subwoofer because the low frequencies aren’t being sent through the amplifier properly. This is why it is important to use a frequency analyzer while connecting your speakers to the old amp; you can tell by the meter how much of the frequencies are being distorted by the resistance in the wiring. A good frequency analyzer will also allow you to experiment with different combinations of wattage and frequency sounds to see what combinations will produce the best sound for your home theater.
Before you connect any speakers to the amp, be sure to unplug the power from the amplifier first. Then, safely position the meter in an area that is far enough away from any wires that could short circuit the meter. Then, plug in the speaker output terminals on the back of the amp. Make sure that the speaker output goes to a connection that can handle the power coming into the amplifier from all the speakers. You may need to experiment with some combinations of wattage and frequency sounds to get the right combination. When testing the connection, the volume level will need to be turned down as low as possible to eliminate potential noise that can come from short circuits.
If you are using a preamp with your amp, then you need to run power from the amp to the preamp input. The preamp will handle the signal that comes through the amplifier; it will not handle the audio output. Some dreams will have their own separate audio input terminals. Others will share a common output terminal with the amplifier itself. After installing the amp and the preamp, power should be run to the speaker terminals on the back of the system. This will allow you to hear any feedback noise that may be present when connecting the speaker units to the amplifier.
If your system is designed to use low-frequency speakers, then you will not be able to hear very far away from the listener. This is why most home systems are designed to be connected to amps with high-quality subs. If you are not using high-quality subs, then connecting the amp and the receiver in this order is often recommended. Remember that the closer you are to the listening position, the smaller your speaker should be. Remember to keep your amplifiers and receivers in good standing height to avoid any excess ground loops.
When using a preamp on your audio system, make sure that the amp has a properly sized input jack. If you connect the sub-woofers into a lower wattage amplifier, then you will not be able to get a deep, powerful bass sound. Most high-quality amps will have a proper setting for the sub-bass frequencies. If you are unsure, then it is best to test out an amplifier before purchasing one. It would also be wise to experiment with different frequency ranges, low and high, to see if you can get the desired result. Once you have found the correct setting for your needs, then you should be ready to enjoy the sweet, deep bass sound from your new equipment!
Connecting a Subwoofer To an Old Amplifier is an easy task. Follow this guide and you will find easy steps.
